White Rodgers 1f80 361 User Manual

5/19/2021/ Comments off

Mar 02, 2016 Buy White Rodgers 1F80-361 Today. Check the White Rodgers 1F80-361 Classic 80 Series Thermostat, Single Stage, 5+1+1 Programmable ratings before checking out. White-Rodgers Home Thermostat. We studied eight excellent White-Rodgers home thermostats over the previous 2 years. Find out which White-Rodgers home thermostat matches you. You can also Narrow by model, type, user interface and Energy Star or opt for one of our White-Rodgers home thermostat feature picks.

1f80-361 White Rodgers Thermostat Manual
White Rodgers Thermostat Troubleshooting
White Rodgers 1f80 361 Troubleshooting
White Rodgers 1f80-361 Thermostat User Manual

Advertising

If the outside temperature is below 50°F, disconnect

If the outside temperature is below 50°F, disconnect
power to the cooling system before programming.

power to the cooling system before programming.

power to the cooling system before programming.
Energizing the air conditioner compressor during cold

Energizing the air conditioner compressor during cold

Energizing the air conditioner compressor during cold
weather may cause personal injury or property damage.

weather may cause personal injury or property damage.

1. Move SYSTEM switch to COOL

COOL

COOL position.

2. Follow the procedure for entering your cooling program,

using your selected cooling times and temperatures.

Enter Cooling Program

CHECK YOUR PROGRAMMING

Follow these steps to check your thermostat programming one
final time before beginning thermostat operation.

1. Move SYSTEM switch to HEAT

HEAT

HEAT position.

2. Press PRGM to view the 1st weekday heating period time

and temperature. Each time you press PRGM, the next
heating period time and temperature will be displayed in
sequence for weekday, then weekend program periods (you
may change any time or temperature during this procedure).

3. Press RUN.

4. Move SYSTEM switch to COOL

COOL

COOL position.

5. Repeat step 2 to check cooling program.

6. Move SYSTEM switch to HEAT

HEAT

HEAT or COOL

COOL

COOL and press RUN to

begin program operation.

YOUR THERMOSTAT IS NOW COMPLETELY PROGRAMMED AND

YOUR THERMOSTAT IS NOW COMPLETELY PROGRAMMED AND
READY TO PROVIDE MAXIMUM COMFORT AND EFFICIENCY!

READY TO PROVIDE MAXIMUM COMFORT AND EFFICIENCY!

Reset Operation

Reset Operation
If a voltage spike or static discharge blanks out the display or
causes erratic thermostat operation you can reset the thermo-

stat by pressing

and TIME at the same time. This also

resets the factory defaults to the configuration menu and

Symptom

Possib

ossib

ossible Cause

le Cause

Corrective Action

No Heat/No Cool/No Fan

1. Blown fuse or tripped circuit breaker.

Replace fuse or reset breaker.

(common problems)

2. Furnace power switch to OFF.

Turn switch to ON.

3. Furnace blower compartment door or

Replace door panel in proper position to engage

panel loose or not properly installed.

safety interlock or door switch.

No Heat

1f80-361 White Rodgers Thermostat Manual

No Heat

1. Pilot light not lit.

Re-light pilot.

2. SYSTEM Switch not set to HEA

HEA

HEAT

Set SYSTEM Switch to Heat

Heat

Heat and raise setpoint

above room temperature.

3. Loose connection to thermostat or system.

Verify thermostat and system wires are securely
attached.

4. Furnace Lock-Out Condition. Heat may also

Many furnaces have safety devices that shut the

be intermittent.

system down when a lock-out condition occurs.
If the heat works intermittently contact the furnace
manufacturer or local service person for assistance.

5. Heating System requires service or

Diagonistic: Set SYSTEM Switch to HEA

HEA

HEAT

T and raise

1f80-361 white rodgers thermostat manual

thermostat requires replacement.

the setpoint above room temperature. Within a few
seconds the thermostat should make a soft click
sound. This sound usually indicates the thermostat
is operating properly. If the thermostat does not
click, try the reset operation listed above. If the
thermostat does not click after being reset contact
your heating and cooling service person or place
of purchase for a replacement. If the thermostat
clicks, contact the furnace manufacturer or a
service person to verify the heating system is
operating correctly.

No Cool

1. SYSTEM Switch not set to COOL

COOL

I plugged the t 3200 into the network using the WAN port. Then I restarted my computer, opened the browser and the Windstream screen appeared. It took a while for Windstream to recognize it and the light to turn green. /actiontec-modem-router-user-manual-t3200.html.

COOL

Set SYSTEM Switch to COOL

COOL

COOL and lower setpoint

below room temperature.

2. Loose connection to thermostat or system.

Verify thermostat and system wires are securely
attached.

3. Cooling System requires service or thermostat

Same procedure as diagnostic for No Heat

requires replacement.

condition except set the thermostat to COOL

COOL

COOL and

lower the setpoint below the room temperature.
There may be up to a five minute delay before
the thermostat clicks in Cooling if the compressor
lock-out option is selected in the configuration
menu (Item 6).

TROUBLESHOOTING

White Rodgers Thermostat Troubleshooting

TROUBLESHOOTING

program. If the thermostat has power, has been reset and still
does not function correctly contact your heating/cooling ser-
vice person or place of purchase.

Batteries

Batteries
For optimum performance, we recommend replacing batteries
once a year with fresh 'AA' alkaline batteries.

CAUTION

White Rodgers 1f80 361 Troubleshooting

Advertising

Popular Brands

White Rodgers 1f80-361 Thermostat User Manual

Popular manuals