Operating Instructions SQ11 mini DV

Charging
Attention! Before using for the first time, fully charge the mini camera battery!

This mini video camera has a built-in lithium-ion battery. You can perform charging in one of the following ways:
1. Connect the mini video camera to the USB port of your PC, stop recording first.
2. Connect the mini camera to a charger from a 220V network or a portable 5V charger. In this case, you can continue to use the mini-camera in the charging process. In the charging process, the blue and red LEDs will light constantly.
After the mini camera battery is fully charged, the blue LED will light constantly and the red LED will turn off.

• If the built-in battery is empty or there is not enough space on the memory card to continue, the blue and red LEDs on the mini camcorder will blink for 5 seconds simultaneously, after which the mini camcorder will save the recorded video and automatically turn off.
• If the memory card is not installed, the blue and red LEDs of the Mini Recorder will blink simultaneously for 5 seconds, after which the Mini Camera will automatically turn off.
• If the camcorder is in the standby mode and does not take any action on it, the camcorder automatically turns off after 1 minute to save the charge of the built-in battery.

Video recording

• Shooting video with a resolution of 1280X720P
Press the «On / Off» button to turn on the mini camera - the blue LED will light up - the mini camcorder is in the video recording standby mode with 720p quality. Press the «On / Off» button once to start recording video - the blue LED will blink 3 times and go out - 720p video is recorded. The video will be automatically saved every 5 minutes. To stop recording, press the «On / Off» button.

• Shooting video with a resolution of 1920X1080P
Press the «On / Off» button to turn on the mini camera - the blue LED will light constantly. Press the «Mode» button once to enter the video capture mode with 1080p resolution - the red and blue LEDs will light simultaneously, the mini camera is in the video recording standby mode with 1080p quality. To start recording, press the «On / Off» button once - the blue LED will go out, and the red LED will blink 3 times and go out - the video is recorded with a quality of 1080p. The video will be automatically saved every 5 minutes. To stop recording, press the «On / Off» button.

• Motion sensor video recording
To do this, while in the 720p or 1080p video recording standby mode, press and hold the «Mode» button of the mini video camera for 3 seconds - the camcorder enters the motion sensor recording mode. If motion is detected, the video recording will start automatically, with red and blue LEDs blinking at the same time. When recording motion sensor, the video recording is automatically saved every 5 minutes.

• Photo
Press the «On / Off» button to turn on the camera - the blue LED will light up. Press the «Mode» button twice to enter the photographing mode - the red LED will stay lit. To take a picture, press the «On / Off» button once - the red LED blinks once, the photo is saved. The resolution of the received photos is 4032x3024.

• Night light
Press the «On / Off» button to turn it on. Press and hold the «On / Off» button for 2 seconds - the red LED will blink twice - the night illumination is on. To turn off the night illumination, press and hold the «On / Off» button for 2 seconds, the red LED will blink three times - the night illumination is turned off.

• Shutdown
To turn off the camcorder, press and hold the «On / Off» button for 6 seconds. If the Mini Camcorder is in the standby mode and is not in use, it automatically turns off after 1 minute.

• Viewing files
Connect the camcorder in the off state to the computer - after a few seconds it will automatically be detected as a removable disk. The blue indicator will indicate the transfer of information, and the red indicator will indicate the charging of the built-in battery.

• Setting the date and time
Connect the mini video camera to the computer. Setting the time is done by creating a text file named «TIMERSET.txt» in the root directory of the device's memory card, with the following content:
«YYYYMMDDHHMMSS» «Y» (or «N», if you do not want the date and time stamp displayed on video files)
For example, «20170625140003 Y»
After saving the file, disconnect the video camera from the computer and turn it on.

Parameters
● Video resolution: 1920x1080, 1280x720
● Frame rate: 15, 30 frames per second
● Video file type: AVI
● Photo resolution: 4032x3024
● Photo file type: JPEG
● Viewing angle: 140 °
● Night illumination: 6 IR LEDs (range of 5 meters, DO NOT emit light!)
● Motion sensor: Yes (range 5 meters)
● Recording while charging: +
● Duration of work:
• 100 minutes (1 hour 40 minutes) in constant recording mode
• About 5 hours in motion sensor mode
• 24/7 24/7 clock when external power is connected
● Support for memory cards: Micro SD up to 64GB
● Cyclic recording: +
● Operating temperature: -10 ° С + 60 ° С
● Humidity of the environment: 15-85%
● Dimensions: 23x23x23 mm, 15 grams

Mini camera SQ11 with night illumination, motion sensor and viewing angle 140 °.
Mini DV SQ11 is an improved version of the previous SQ8 and SQ9

The camera SQ11 has a built-in motion sensor, can shoot photos with a resolution of 4032x3024, and can also be used for recording in the process of charging from a 220V network or portable chargers, which increases the battery life by 30-40 times.

User Manual

• Characters of Product

Operation Guide:

• Charge

• Power on to video

• Sound control video (optional)

• Time set

• Power off

• Auto-power off function

• Connecting computer

• PC Camera Canon dvd camcorder dc201 user manual.

• Reset

• Notice

• Characters of Product

• It has small contour design, which does UV spray finishing for the whole body. It is very fashionable and wearable and matches with all kinds of portable tools.
• Support PC camera and chatting function.
• Support AVI video format.
• It can carry out high definition image recording under low illumination.
• Support 30 fps for 720*480
• Support USB1.1 and USB2.0.
• Support 8GB T-flash card.(maximum)
• Build-in lithium battery which can make a video more than two hours

Operation Guide

• Charge

The battery is built-in lithium rechargeable battery, so when you use it the first time, please charge firstly. The method for charging as following:

1. Connect computer: use USB cable to connect the computer, then it can be charged.

2. Use adaptor: connect charger plug with USB cable, then plug into electrical connector receptacle, it can be charged.

When you charge it, green light and red light will bright simultaneously, of which states are stillness.

Notice: when battery power is not enough, MD80 will enter into protection mode, so it cannot be turn on. Now, please charge for it.

• Power on to video

Press «Power» button slightly, yellow indicator light begins to bright, now it enters into startup ready mode, which can enter into standby mode quickly. Press «Record / Stop» button slightly, yellow indicator light begins to bright, red indicator light starts to flash slowly. At this time, it begins to make a video. The resolution for video file is 720*480, and frame number is 29--30fps/S. Then short press «Record / Stop» button, video is stopped and saved automatically. After saving the red indicator light remains light. If you need to continue to video, please press «Record / Stop» button slightly once more.

Notice:

a. Please make sure T-flash (Micro SD) card has been inserted, if not, it will be power off automatically after 30 seconds.

b. The maximum capacity of T-flash card is 8GB.

c. Saving file needs certain time, so please don’t press Operation button continuously in order to avoid saving unsmoothly and generating incomplete file.

d. When you make a video, please focus on the object and keep 50cm under sufficient illumination. Then the video will be right, natural color, clear and stable.

• Sound control video (optional)

Press «Power» button slightly, yellow indicator light begins to bright, now it enters into startup ready mode, which can enter into standby mode quickly. At that time, press «MODE» button slightly, and then you can switch into sound control video mode. Now yellow indicator light always brights, red indicator light flash quickly (indicate sound control standby mode). When decibel of video is more than 60, then it will be video automatically. At the moment, yellow indicator light always brights, red indicator light flash slowly. (Indicate under sound control video) When sound control starts, the shortest shoot time is 2 minutes. After 2 minutes, if there is no any sound, MD80 will save file automatically and switch into standby mode. If there still has sound after 2 minutes, MD80 will continue to shoot.

• Time set

There is a CD with the product which contains a file named time synchronization file. Please copy it to TF card. When connect MD80 with computer, whose time will be displayed with computer synchronously

The detail as following:

1 > build a text called «TAG.TXT» under root directory of card.

2 > open «TAG.TXT», write synchronous date according to enclosure stricktly

Details as following:

[date] need space with newline

2017/07/22 need space with newline 12：00：00

3 > Copy the file «TAG.TXT» to the TF card in MD80, then pull out from computer and power off.

4 > Power on the machine MD80 everytime, system will check and analyse «TAG.TXT», then set system time according to file time. After that the text will be deleted by system automatically.

• Power off

Under video mode or standby mode, please long press Power button 3 seconds, then release till indicator goes out. Then the machine is turned off.

• Auto-power off function

MINI DV MD80 will save file and turn off automatically as following:

a. When you shoot video without enough power, file will be saved automatically, then auto-power off.

b. When disk space of MINI DV MD80 is not enoughn, after indicator goes out immediately, file will be saved automatically then auto-power off.

c. Under standby mode, without any operation in 45 seconds, it will be auto-power off

• Connecting computer

It can connects computer under power off mode, standby mode or video mode, after that which can be used as U disk, who can copy, cut and paste, delete file. When you connect it with USB port, a portable disk mark will be seen after several seconds. Red indicator light always brights, yellow indicator light will be from flashed quickly to always brights.

Notice:

a. When you connect computer, if the machine cannot be identified, or not see the portable U disk mark in 30 seconds, please insert it again.

b. It is better copy or cut video file into computer hardware then play. Video file which is saved in the machine is played directly will cause unsmooth play, the reason is that gigantic data cannot be transmitted synchronously.

• PC Camera

When you first use PC camera, please install driver. The driver name is SPCA1528_V2220_M…Setup.exe, which is placed in attached CD. When you install please double press this document, and as per guide to do. After that there will be an AMCAP icon on the computer desk

Under power off or power on mode, use USB cable to connect computer, the mode is U disk mode. Then short press «MODE» button, at this moment it can be switched into PC camera mode. Then double press AMCAP icon can be used as PC camera.

• Reset

When machine works abnormal for illegal operation or other unknown reasons, it needs to be reset.

The specific operation method as following:

Use slim pole to press the Reset button, and then finish one reset operation.

• Notice

Suitable using situation: Please follow State's law. Do not use it illegally.

Software upgrade: In order to make products have more function, manufacturer will perfect product software continuously. This product is convenient for customer to upgrade by themselves, so please contact with local retailer for the latest software information and upgrade method

Work temperature: Please use it under normal temperature and avoid using under unsuitable body temperature.

Work humidity: Please use it under agreeable human atmosphere humidity, Please not to make product wet or expose in rain for which without waterproop function.

Shooting illumination: Please use it under enough light sources; do not aim the camera at the sun and other strong light sources in order not to damage optical parts of an apparatus.

Cleaning requirements: Please not use the product under too large dust density atmosphere so as not to affect video effects for tainted lens and other parts.

Waste treatment: Please pay attention to protect environment, not to throw the product optionally. In order to avoid explosion, please not throw product into fire.

Introduction:№ 1№ 2№ 3