Innotech Maxim Series 2 User Manual
Innotech MAXIM II Manuals Manuals and User Guides for Innotech MAXIM II. We have 1 Innotech MAXIM II manual available for free PDF download: Installation. Table 1-2: Features Of MAXIM Series Controllers 12. 1-2.2 Sub System Network Controllers 13. 1-2.3 Sub System Gateway (IG01) 13. DS 10.06 - MAXIM 1010 - Digital Controller October 2013 Associated Software MAXCon is the configuration utility for the MAXIM family of controllers. It allows the user to internally configure a MAXIM 1010 controller by using a simple point-and-click approach on a Windows® based computer. MAXMon is a monitoring and debugging utility designed to. Innotech Adelaide South Australia Distributor, Electrical Contracor, BMS controls, DDC Controls, Energy Management Controls. Dec 15, 2014 Issuu is a digital publishing platform that makes it simple to publish magazines, catalogs, newspapers, books, and more online. Easily share your publications and get them in front of Issuu’s.
MAXIM Installation Instructions
Page 30
Series download sites for mobile phones. © Mass Electronics Pty Ltd 2011
Edition 2.0 dated 20/11/2013
3-3.1.3 Analogue Outputs
The analogue outputs can be configured with MAXCon software to either heat valve mode or variable
mode to suit your requirements. Each analogue output has a signal terminal (+) and a shared Com
terminal (–). As illustrated in the connection details in Figure 3-1, the + terminal is the active signal,
and the Com terminal is the signal reference of 0V, which also can be referred to as ground.
It must be noted that on MAXIM Series I and II controllers only AO1 and AO2 can be configured to heat
valve mode. However on MAXIM Series III all 8 Analogue Outputs can be configured to heat valve
mode.
When an analogue output is configured to heat valve mode, the output is a Pulse Width Modulated
(PWM) signal of 0 or 10V DC with a maximum current rating of 5m A. When an analogue output is
configured to variable mode, the output is an analogue voltage signal varying from 0 to 10V DC with a
maximum current rating of 5m A.
When an analogue output is configured as a PWM signal in heat valve mode, up to three Solid State
Suzuki WagonR Manual 92 pages. Related Manuals for Suzuki WagonR. Automobile Suzuki Wagon R Owner's Manual. Owners manual for suzuki wagon r car (108 pages) Automobile Suzuki Wagon R Manual (4424 pages) Automobile Suzuki Samurai 2 WD 1991 Supplementary Service Manual. Vivek Singh Jan 16, 2018 08:48. View and Download Suzuki Wagon R owner's manual online. Owners manual for Suzuki Wagon R car. Wagon R Automobile pdf manual download. Please e mail me this user manual for Suzuki Wagon R 2014 as i could not down load it despite efforts. My e mail address is given below. ASHIS KUMAR BANERJEE Sep 04, 2018 08:53. Suzuki wagon r hybrid 2018 user manual. A customised One-Of-A-Kind Motor Insurance Policy for vehicle owners. Maruti Suzuki Genuine Parts Keep your car as good as new with Maruti Suzuki Genuine parts.
Relays (SSR) connected in series may be used on each analogue output channel, as illustrated in
Figure 3-6 below. The SSRs must be capable of a trigger voltage of 3 to 32V DC and zero switching.
1
2
3+ve
4
1
2
3+ve
4
1
2
3+ve
4
+
-
ANALOGUE
Innotech Maxim Series 3 Manual
OUTPUT
TERMINALS
TO
HEATERS
TO
HEATERS
TO
Innotech Maxim Series 2 Manual
HEATERS
L1
L2
Innotech Maxim Series 3 User Manual
L3
If up to 6 SSRs are to be wired in series, you can use the Analogue Output as 0 to 10V DC modulating
in conjunction with the Innotech Heat Valve (IHV) module. Please refer to the following datasheets
for more information on IHVs:
• DS3.31 for IHV Heat Valves
• DS3.32 for IHV42 Heat Valves
Figure 3-6: Analogue Output Driving Multiple Solid State Relays