1771-ife Series A User Manual
1771 Ife A
Analog input module, Installation instructions, Catalog number 1771-ife/c)
Publication 1771Ć5.45 - July 1997
Here’s a complete guide on what’s in iOS 9, how to download it, and a list of iPhone and iPad users who shouldn’t download the update.Before we get into how to download it, we’ve got a pretty big disclaimer for the newbies out there: Software updates are often unstable. That said, iOS updates aren’t typically too crazy, so you should be fine. Jessica Lee Star/Digital TrendsIf you’ve been anxiously awaiting the iOS 9 update, today’s the day you can download the final version on your iPhone and iPad. /manual-download-of-ios-9.html. If you download iOS 9 on the first day or on an older device, you may experience random crashes, weird reactions from apps, battery drain, and other issues. Just know that there is a risk of performance issues with new software.Related Offer:If things get too hairy, you can always downgrade back to iOS 8.4 (we’ll tell you how — Apple’s got a nice guide setup, too).
Analog Input Module
Assembly cat. 1771-IF Series A, not covered in this manual, will not accommodate Expanders. Expander Modules provide a method of increasing the input point capacity of a system that is more economical, in cost as well as in module space, than using more Analog Input Modules. The 1771-E1 accepts up to eight single-ended input points (+5V DC, +1.
(Catalog Number 1771-IFE/C)
Use this document as a guide when installing the 1771-IFE/C analog
input module.
To
See page
Prevent Electrostatic Discharge
Below
Understand Compliance to European Union Directives
Understand Product Compatibility
Calculate Power Requirements
Buy and use a torque wrench to prevent common over-tightening problems and avoid expensive fixes later. This Kobalt 1/2-in. Drive 50– 250 ft. Consult your owner's manual or a shop manual and set your torque wrench to one-half. Find the cheap Torque Wrench Tool, Find the best Torque Wrench Tool deals, Sourcing the. Kobalt digital torque wrench user manual. Kobalt 1/2-in Drive Programmable Electronic Torque Wrench (12.5-ft lb to 250-ft lb) at Lowe's. This new 12.5 - 250 ft-lb 1/2-in drive torque wrench operates in both digital and angle modes, allowing the user to fulfill the specifications designated.
Determine Module Placement
Set the A/B Simulation Jumper
Set the Configuration Jumpers
Key the Backplane Connector
Install the Module and Field Wiring Arm
Connect Wiring to the Field Wiring Arm
Ground the Chassis and Module
Configure the Module
For this reference information
See page
Status Indicators
Troubleshooting
Specifications
CSA Hazardous Approval
Differences Between Series A, B and C Modules
The analog input module is sensitive to electrostatic discharge.
!
ATTENTION: Electrostatic discharge can damage
integrated circuits or semiconductors if you touch
backplane connector pins. Follow these guidelines
when you handle the module:
•
Touch a grounded object to discharge static potential
•
Wear an approved wrist-strap grounding device
•
Do not touch the backplane connector or
connector pins
•
Do not touch circuit components inside the module
•
If available, use a static-safe work station
•
When not in use, keep the module in its
static-shield box
This icon is used when
additional information
is available in the Analog
Input Module User Manual,
publication 1771Ć6.5.115.
If you need a copy of this
manual, fax the enclosed
User Manual Request Card
to 1Ć800Ć576Ć6340. If you
are outside the U.S., fax the
card to1Ć330Ć723Ć4036.
Installation Instructions
Contents
Prevent Electrostatic
Discharge
1771 Ife Wiring
Ab 1771 Ife
User Manual
Analog Input
Module
(Cat. No. 1771ĆIFE Series C)
AllenĆBradley
- 1771-6.5.115, Analog Input Module, User Manual
- Summary of Changes
- Preface - Using This Manual
- 1 - Overview of the Analog Input Module
- 2 - Installing the Input Module
- 3 - Module Programming
- 4 - Configuring Your Module
- 5 - Module Status and Input Data
- 6 - Calibrating Your Module
- 7 - Troubleshooting Your Input Module
- C - Programming Examples
- D - Data Table Formats
- E - Block Transfer (Mini-PLC-2 and PLC-2/20 Processors)
- F - Forms